fbpx

DPA 4017B Shotgun Mic

$3,145.00

The DPA 4017B Shotgun Microphone is designed for a broad range of applications, this microphone is ideal for use with camera systems, in fixed positions at sports facilities, for broadcast / ENG / film booming and even studio recording environments.

Available on backorder

At just 210 mm (8.3 in) and 68 g (2.4 oz), the DPA 4017B is one of the shortest and lightest shotgun condenser microphones available. At the same time, it offers impressive accuracy, clarity and musicality. The mic is immune to RF emission and the 19 mm (0.75 in) condenser cartridge is capable of handling peak SPLs of 152 dB before clipping. It also withstands use in very humid environments with ease.

The DPA 4017B Shotgun Microphone features two onboard filters. They are activated via an ingenious switching ring design. With a simple twist of two sturdy rings, engineers can implement a high-frequency boost that adds a 4 dB shelf at 8 kHz. This compensates for hi loss when used with windjammers. A first-order bass roll-off below 120 Hz minimises handling and wind noise. A permanent third-order high-pass filter at 50 Hz effectively removes unwanted low frequency disturbance from handling and wind noise.

This solution is also available with Rycote® Windshield and suspension system – a fully-packed and ready-to-go solution.

Specifications

Directional pattern Supercardioid, lobe-shaped
Principle of operation Pressure gradient, with interference tube
Cartridge type Pre-polarized condenser
Frequency response 20 Hz – 20 kHz, permanent third order high pass filter at 50 Hz
Frequency range, ±2 dB, at 60 cm (23.6 in) 70 Hz – 18 kHz with typ. 3 dB soft boost at 15 kHz
Sensitivity, nominal, ±2 dB at 1 kHz 19 mV/Pa; -34.4 dB re. 1 V/Pa
Equivalent noise level, A-weighted Typ. 13 dB(A) re. 20 µPa (max. 15 dB(A))
Equivalent noise level, ITU-R BS.468-4 Typ. 24 dB (max. 26 dB)
Distortion, THD < 1% 134 dB SPL RMS, 137 dB SPL peak
Dynamic range Typ. 124 dB
Max. SPL, THD 10% 138 dB SPL peak
Switchable attenuator, filters etc. High boost: +4 dB at 8 kHz. Low cut: First order filter, below 120 Hz
Rated output impedance 100 Ω
Minimum load impedance 2 kΩ
Cable drive capability 100 m (328 ft)
Output balance principle Signal balanced
Common mode rejection ratio (CMRR) > 40 dB
Power supply (for full performance) P48 (Phantom power)
Current consumption 4.5 mA
Connector XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: signal – phase
Colour Matte black
Weight 68 g (2.4 oz)
Microphone diameter 19 mm (0.75 in)
Capsule diameter 19 mm (0.75 in)
Microphone length 212 mm (8.3 in)
Maximum output voltage, RMS 2.0 V
Polarity +V at pin 2 for positive sound pressure
Temperature range -40°C to 45°C (-40°F to 113°F)
Relative humidity (RH) Up to 90%

Reviews

There are no reviews yet.

Be the first to review “DPA 4017B Shotgun Mic”

Your email address will not be published. Required fields are marked *

Copyright ©2024 AKA Pro Audio Pty Ltd. All rights reserved. | Privacy Policy | Terms of Use
© 2024 AKA Pro Audio Pty Ltd. All rights reserved. | Privacy Policy | Terms of Use